Corn silage bales are small round bales of chopped, kernel-processed whole-plant maize, sealed in stretch film so the forage ferments into silage inside each bale. They are not the same thing as the wrapped grass bales most people picture when they hear “baled silage”. Grass baleage is long, wilted forage made at 40 to 60 percent dry matter; corn silage bales are chopped maize harvested at much the same moisture as clamp or bag silage, and they ferment more fully as a result. Making them well comes down to four decisions: when to harvest, how long to chop, whether the kernels are properly cracked, and how quickly and carefully the bales are sealed. This guide works through each one with published figures, so you can set the machine and judge the result rather than guess.

making corn silage bales with an all-in-one silage baler wrapper, chopped maize baled and wrapped in the field

Chopped Maize Bales Are Not Baleage

The distinction matters because the rules are different. Advice written for wrapped grass bales, including our own guide to silage bales, assumes long forage baled from a windrow after wilting in the field. Corn silage bales start from a standing crop that is cut, chopped and processed in one operation, usually by a forage harvester feeding a baler, or by an all-in-one silage harvester baler that does every step itself.

Grass baleage Corn silage bales
Crop Grass, legumes, whole crop cereals Whole-plant maize, sometimes forage grass
Form Long, unchopped or lightly cut Chopped to a set length, kernels cracked
Harvest moisture Wilted to roughly 40 to 60 percent dry matter Harvested standing, roughly 30 to 40 percent dry matter
Fermentation Lighter and slower, finishes at a higher pH Fuller, closer to bunker or bag corn silage
Main nutritional value Protein and digestible fibre Energy from starch, plus fibre

The practical consequence is that corn silage bales behave much more like a small, sealed bag silo than like hay that has been wrapped. They are packed denser, they hold more water, and their value depends heavily on the starch in the grain, which is why kernel processing appears in this guide at all. If you are used to making grass baleage, expect to set your harvest timing by the maize crop’s moisture, not by how long the swath has been wilting.

Harvest Moisture: Treat Bales Like Bags

Whole-plant moisture is the first decision and the one that affects everything else. University of Wisconsin guidance sets ideal whole-plant moisture by storage structure: 65 to 70 percent for horizontal bunkers and 60 to 70 percent for bag silos. Sealed bales are physically closest to bags, small airtight packages with no open face, so the bag range is the sensible target. In dry matter terms that is roughly 30 to 40 percent.

Missing the window costs you in both directions. According to the same guidance, harvesting too wet reduces yield and causes souring and seepage, with lower intake by dairy cows. In a sealed bale, seepage also means effluent pooling inside the film, and heavy, slumping bales that are harder to handle. Harvesting too dry also reduces yield, can let mould develop, and lowers digestibility, protein and vitamins A and E. Dry chopped maize is springier and harder to compress, so dry bales hold more air, and air is what turns into mould.

Two practical points from the Wisconsin guidance are worth keeping in mind. First, the kernel milk line is not a reliable indicator of harvest timing on its own; use it as the signal to start sampling, then measure moisture directly. Second, for planning, whole-plant dry-down can be assumed at around half a percentage point per day in early autumn, with county averages measured between 0.4 and 0.7 percent per day. That tells you roughly how many days you have once the crop reaches the edge of the range. Measuring is quick: a microwave oven, a kitchen scale and a few hundred grams of chopped sample will give you a dry matter figure in about twenty minutes.

Chop Length: 10 or 20 mm

Chop length, often called theoretical length of cut, is a balance. Shorter chop packs more densely and excludes air more easily, which helps fermentation and makes a tighter bale. Longer chop keeps more physically effective fibre, the coarse material that makes cows chew and protects the rumen, which matters in rations where maize silage is a large share of the forage.

Guidelines summarised by UC Davis Cooperative Extension tie the right setting to crop dry matter. For kernel-processed maize below 33 percent dry matter, the recommended theoretical length of cut is 0.75 to 0.90 inches, roughly 19 to 23 mm, with the processor rolls open. Between 33 and 38 percent dry matter, the same length applies with a small roll clearance of about 0.12 inches. At 38 percent and above, the recommendation drops to 0.5 inches, about 13 mm, with the rolls closed, because drier crop needs to be chopped finer to pack.

Mapped onto a machine with fixed 10 and 20 mm settings, such as the 9QZ-2150A, the logic becomes simple. The 20 mm setting sits squarely in the recommended range for crop in the normal harvest window. The 10 mm setting is the one to reach for when the crop has dried past the ideal and needs finer chopping to pack, or when your nutritionist wants a finer particle size for the ration. If you are unsure, start at 20 mm in a crop within the target moisture range and check bale density and the finished silage.

two-drum maize header and cab of a silage harvester that chops and kernel-processes corn for silage bales

Kernel Processing: The Step That Decides Energy Value

A maize kernel has a hard outer coat. Swallowed whole, a good share of kernels pass through a cow without being digested, and the starch inside them, which is most of maize silage’s energy, is lost. Kernel processing cracks or crushes the kernels at harvest so that rumen microbes and enzymes can reach the starch. On machines that offer it, it is one of the most valuable settings on the whole harvest.

The standard measure is the kernel processing score, the percentage of starch that passes through a coarse sieve in a laboratory test. As summarised by UC Davis, processing is excellent when more than 70 percent of starch passes, adequate between 50 and 70 percent, and poor below 50 percent. The same source describes adequate processing as most kernels cracked, at least 95 percent, with most kernel particles smaller than a quarter of a kernel.

You do not need a laboratory to check in the field. Drop a handful of freshly chopped forage into a bucket of water and stir: the kernel pieces sink while the leaf and stalk float, so you can pour off the light material and look at what remains. Whole or merely nicked kernels mean the processor needs adjusting. Check at the start of each field and whenever crop moisture changes noticeably, because a setting that works on wetter crop can leave drier, harder kernels intact. Send a sample to a forage laboratory for a kernel processing score once or twice a season to confirm what your eyes are telling you.

Wrapping, Handling and Storing the Bales

A corn silage bale is only as good as its seal. Chopped maize is dense and heavy, so a sealed bale ferments quickly, but any air that gets in through a gap or puncture feeds yeasts and moulds, and once a well-fermented bale is exposed to air it can heat and spoil quickly. Wrap immediately after forming; machines that bale and wrap in one pass do this automatically, while separate baling and wrapping should be arranged so no bale waits.

On layers, the general guidance for wrapped bales is a minimum of four layers of film and six for longer storage, bales that will be moved several times, or warm climates. Chopped maize is less likely than stemmy lucerne to puncture film from the inside, but cut stalk ends can still pierce a thin wrap, so do not cut corners on layer count. Our guide to how many times to wrap a bale sets out the reasoning, and film for small bales is covered in our article on the 250 mm silage film baler.

Handle bales by the body with a grab or clamp rather than a spike, move them to storage soon after wrapping, and store them on level, firm, clean ground away from trees and long grass where rodents and birds shelter. Walk the stack regularly and patch any hole the day you find it with UV-stable silage tape. Small bales are often stacked two or three high; our guide on stacking silage safely covers how to do that without crushing the bottom row or creating an unstable pile.

rear bale wrapper with silage film roll sealing a corn silage bale

Fermentation Time and Feeding Out

Give the bales time before opening them. Most of the active fermentation in maize silage happens in the first few weeks, and a common rule of thumb is to wait at least three weeks before feeding. Waiting longer does no harm: research on stored corn silage has found that starch digestibility continues to improve over several months of storage, so bales opened later in the season can feed slightly better than the same silage opened early.

Small bales have a real advantage at feed-out. A bunker has to be fed fast enough to stay ahead of spoilage at the open face, which sets a minimum herd size for the bunker to make sense. A bale is opened whole and fed within a day or so, so the amount exposed to air matches the amount fed. Strip the film and any net completely before feeding, since fragments eaten by cattle can cause digestive problems, and feed opened bales quickly in hot weather. Corn silage bales fit straight into a mixed ration; our article on how a TMR mixer works covers mixing, and our guide to corn silage covers its place in dairy and beef rations.

Judging Quality in the Bale

Good corn silage smells clean, mildly sour and slightly fruity, is yellow-green to light brown, and feels moist without dripping. Warning signs are a vinegary or alcoholic smell, which points to too much acetic acid or yeast activity; a rancid or putrid smell, which suggests poor fermentation; visible mould; or heat when you put a hand into the forage. Discard visibly mouldy or rotten sections, and if a whole bale smells putrid or rancid, discard the bale rather than trying to salvage part of it.

For numbers, send samples to a forage laboratory. Dry matter, starch, fibre and kernel processing score tell you whether harvest settings delivered what you intended, and give your nutritionist what they need to balance the ration. Comparing results from different fields or harvest days is the fastest way to learn which settings work on your farm.

Common Mistakes and How to Avoid Them

Mistake What it causes How to avoid it
Harvesting by calendar or milk line only Bales that are too wet or too dry Sample and measure whole-plant moisture; aim for roughly 60 to 70 percent
Long chop on dry crop Springy, poorly packed bales with trapped air Switch to the shorter setting as dry matter rises
Never checking the kernel processor Whole kernels and wasted starch Bucket test at the start of each field; lab score once or twice a season
Too few film layers Punctures, air entry, mouldy patches At least four layers; six for long storage or rough handling
Spiking or dropping bales Film damage and spoilage Use a grab, handle gently, move to storage soon after wrapping
Opening bales too early Incompletely fermented silage Wait at least three weeks; longer storage can improve starch digestibility

Equipment for Corn Silage Bales

Corn silage bales can be made two ways: a forage harvester chopping into a trailer, with the chopped forage then fed into a stationary baler-wrapper such as the BalerPro 55; or a single self-propelled machine that harvests, chops, processes, bales and wraps in one pass. Tsingtao Jummos Agricultural Technology Co., Ltd., based at No.173 Jufeng Road, Qingdao, China, supplies equipment for both: stationary baler-wrappers for the first route and the 9QZ-2150A all-in-one machine for the second, and supplies silage film through its sister brand Silopak. Tell us your crop area, herd size and harvest arrangements, and we will recommend the route that fits.

Frequently Asked Questions

What moisture should corn be when making silage bales?

Roughly 60 to 70 percent whole-plant moisture, which is 30 to 40 percent dry matter. That is the University of Wisconsin range for bag silos, the closest storage type to sealed bales. Wetter crop causes seepage and souring; drier crop packs poorly and risks mould.

What chop length is best for corn silage bales?

For kernel-processed maize in the normal harvest window, guidelines suggest about 19 to 23 mm, so a 20 mm setting fits well. If the crop has dried to 38 percent dry matter or more, a shorter cut of around 13 mm or less helps it pack, so a 10 mm setting is the better choice.

How do I know if the kernels are processed properly?

Put a handful of fresh chopped forage in a bucket of water; the kernel pieces sink and the rest floats. If you see whole or barely nicked kernels, adjust the processor. A laboratory kernel processing score above 70 percent is excellent, 50 to 70 percent adequate, and below 50 percent poor.

How long before I can feed corn silage bales?

Wait at least three weeks so fermentation can stabilise. Longer storage does no harm and can improve starch digestibility over several months, provided the film stays intact.

How are corn silage bales different from grass baleage?

Corn silage bales are chopped, kernel-processed maize harvested at roughly 30 to 40 percent dry matter, and they ferment fully like bag or bunker silage. Grass baleage is long forage wilted to 40 to 60 percent dry matter, which ferments more lightly. The two follow different rules for harvest timing and handling.


Reviewed by Sue Su, Marketing Director at Tsingtao Jummos Agricultural Technology Co., Ltd., a supplier of baler wrappers, silage harvesting equipment, TMR mixers and manure handling equipment based in Qingdao, China. Last reviewed 19 November 2026.