There are two basic ways to turn a field of standing maize into stored silage. In the first, chop-and-haul, a forage harvester chops the crop into trucks or trailers, which carry it to a bunker, a pile or a bag where it is packed and covered. In the second, harvest-and-bale, the chopped crop is pressed into sealed bales in the field, either by a forage harvester feeding a separate baler-wrapper or by a single all-in-one machine that does every step itself. Neither system is better in general. Chop-and-haul wins on cost per tonne at scale; harvest-and-bale wins on crew size, timing flexibility and feed-out at small scale. This article sets out where the real differences lie, with a way to compare the two using your own numbers, so the choice is made on arithmetic rather than habit.
What Each System Actually Involves
The two systems differ less in the harvester than in everything around it. Chop-and-haul is a chain: the harvester is the visible part, but it cannot run without enough trucks to carry its output away and a packing tractor at the clamp to spread and compact each load. Harvest-and-bale moves the packing and sealing into the field, so the forage leaves the harvest area already protected.
| Chop-and-haul | Harvest-and-bale (all-in-one) | |
|---|---|---|
| Machines on harvest day | Forage harvester, several trucks or trailers, packing tractor | One self-propelled harvester baler wrapper |
| People on harvest day | Harvester operator, a driver per truck, packing tractor driver | One operator |
| Storage | Bunker, drive-over pile or silage bag | Sealed bales stored on any firm, level ground |
| Timing pressure | Every link must keep pace; forage waits if one fails | Bales sealed as made; collection can wait days |
| Throughput | High, if trucks keep up | Moderate: 45 to 60 bales per hour |
| Feed-out | From an open face at a minimum daily rate | One bale at a time |
| Plastic per tonne | Low: one cover over the whole clamp | Higher: every bale wrapped individually |
A third route sits between them: chopping with a conventional harvester into trailers, then feeding the chopped forage into a stationary baler-wrapper in the yard. It keeps the bale format but still needs the transport chain, so it shares some strengths and some weaknesses of each. The all-in-one approach, described in our article on the all-in-one silage harvester baler, is the version that removes transport from harvest day altogether.
Compare Person-Hours, Not Machine Speed
The most common mistake in comparing the two systems is to compare the harvesters alone. A conventional forage harvester chops far more tonnes per hour than any all-in-one machine, so on that measure the comparison is over before it starts. But a forage harvester never works alone, and the number that drives labour cost is person-hours per tonne across the whole operation.
The calculation is simple. Divide the crew size by the system’s throughput in tonnes per hour, and you have person-hours per tonne. Multiply by your annual silage tonnage and you have the total. For an all-in-one machine rated at 45 to 60 bales an hour, throughput depends on bale weight: at around 90 kg per bale it is roughly 4 to 5.4 tonnes an hour, with one person. Making 300 tonnes of silage would then take somewhere around 56 to 75 hours of machine time, and the same number of person-hours, plus the time needed later to collect bales from the field.
Now take an illustrative chop-and-haul operation. Suppose a contractor’s harvester averages 20 tonnes an hour, supported by two trucks and one packing tractor, a crew of four. The same 300 tonnes takes 15 hours of harvest time and 60 person-hours. Substitute your own figures; the point of the example is the shape of the result, not the numbers. In many realistic cases the total person-hours of the two systems are closer than the difference in machine speed suggests. What differs is how those hours are distributed: chop-and-haul concentrates them into a few intense days that need a full crew at once, while harvest-and-bale spreads them across more days with one person.
That distribution is often the deciding factor. A farm that can reliably assemble four people and three or four machines on the right two days, or that has a dependable contractor, will find chop-and-haul efficient. A farm that cannot, because labour is scarce, contractors are booked solid at harvest, or fields ripen at different times, may find that one person working steadily over a week produces better silage than a crew that arrives late.
Distance and Transport
Maize silage at harvest is roughly 60 to 70 percent water, so a chop-and-haul system spends most of its transport effort moving water. When fields are close to the clamp, that hardly matters. When they are several kilometres away, or scattered across many small plots, each extra kilometre adds truck time, and the number of trucks needed to keep the harvester busy rises with it. Long or uneven haul distances are where chop-and-haul systems most often break down, with the harvester standing idle waiting for trucks or trucks queueing at a congested clamp.
Harvest-and-bale still has to move the same water eventually, because the bales weigh what the forage weighs. The difference is timing. Sealed bales can be collected after harvest, at whatever pace the farm’s loader and trailer allow, without the silage deteriorating while it waits. Transport becomes a background job rather than the bottleneck that sets the pace of the whole harvest. For farms with fields spread over a wide area, that change alone can justify the system.
Storage and Feed-Out Set a Minimum Scale
A bunker or pile has to be fed out fast enough to stay ahead of spoilage at the open face. University of Wisconsin Extension recommends removing at least 6 inches, about 15 centimetres, of the face per day in summer and 4 inches, about 10 centimetres, in winter. That rule sets a minimum herd size for any given bunker: a clamp that is too wide for the number of animals it feeds will lose feed at the face every day, however well it was made. Our guide to bunker silos shows how to size a bunker from the feed-out rate.
Bales remove that constraint. Each bale is opened whole and fed within a day or so, so the amount of silage exposed to air always matches the amount being fed. A herd of twenty cows and a herd of two hundred can both feed from bales without a face to manage. Bales also need no permanent structure, only firm, level, clean ground, and storage capacity grows simply by making more bales. For farms without a bunker, or with too few animals to keep one moving, that flexibility is often worth more than the bunker’s lower cost per tonne. Silage bags offer a middle path, and our article on silage bags covers that option.
Losses: Where Each System Leaks
Both systems lose some dry matter between harvest and feeding, but in different places. In a bunker, losses depend heavily on how densely the silage is packed. University of Wisconsin figures for alfalfa silage show dry matter loss after 180 days falling from about 20 percent at a density of 10 lb DM per cubic foot to about 10 percent at 22 lb, which is why packing is the most important job at the clamp. Losses also concentrate at the surface, the shoulders and the face, where air gets in.
In sealed bales, losses depend mainly on the film. A bale that stays airtight from harvest to feeding loses little; a bale with a puncture or a torn edge can spoil around the damage and sometimes throughout. Losses in a bale system therefore come down to wrapping enough layers, handling bales gently, storing them where birds and rodents cannot reach them, and repairing any hole the day it appears. Our practical guide to corn silage bales covers how to make and store them so the film does its job.
There is one more difference worth noting. In a bunker, a packing or covering problem affects a large volume of silage at once. In bales, a problem usually affects individual bales, which can be identified and discarded while the rest of the stock stays sound. Risk is spread across many small units rather than concentrated in one.
We sell bale equipment, and we still tell customers when a clamp would serve them better. The honest answer is that big herds with good contractors and a bunker usually make cheaper silage by chopping into the clamp. Smaller farms, scattered fields and anyone who can’t count on a crew on the right day often do better with bales. The worst outcome is choosing a system that needs more people or more scale than you actually have. Sue Su, Marketing Director, Tsingtao Jummos Agricultural Technology Co., Ltd.
Plastic Per Tonne: The Honest Disadvantage of Small Bales
Bales use more plastic per tonne of silage than a bunker, and small bales use more than large ones. The reason is geometry. A round bale of 55 cm by 52 cm has a surface area of about 1.37 square metres for a volume of about 0.12 cubic metres, roughly 11.1 square metres of surface per cubic metre of silage. A large round bale of 1.2 by 1.2 metres has about 5.0 square metres per cubic metre. Before counting layers, a small bale therefore needs roughly 2.2 times as much film per cubic metre of silage as a large one.
That shows up in two places: the cost of film, worked through in our article on bale wrapping cost, and the volume of used plastic the farm has to dispose of or recycle. Neither is a reason to rule out small bales, because the benefits in handling, labour and feed-out can outweigh them, but both should be in the budget and the farm’s waste plan from the start. A bunker system uses far less plastic per tonne, which is one of the main reasons it wins on cost at scale.
Which System Suits Which Farm
| Situation | Usually better fit | Why |
|---|---|---|
| Large herd, bunker already built, reliable contractor | Chop-and-haul | Lowest cost per tonne, high throughput, little plastic |
| Small or medium herd, no bunker | Harvest-and-bale | No structure needed, feed-out matches herd size |
| Fields scattered or far from the yard | Harvest-and-bale | Transport no longer sets the pace of harvest |
| Harvest labour scarce or contractors unreliable | Harvest-and-bale | One operator, harvest when the crop is ready |
| Business selling silage to other farms | Harvest-and-bale | Bales are a saleable, transportable unit |
| Very large tonnage in a short harvest window | Chop-and-haul | Only a full chain moves enough tonnes per day |
| Mixed: main crop plus later or smaller cuts | Both | Bunker for the bulk, bales for the remainder |
Plenty of farms end up using both. A clamp for the main maize crop and bales for later cuts, outlying fields or silage for sale is a common and sensible combination. The question is not which system is right in principle, but which one, or which mix, matches your herd, your fields, your labour and your market.
Running the Numbers for Your Farm
To compare the systems properly, collect a few figures before talking to any supplier. Annual silage tonnage, the distance from each field to the storage site, the number of people you can reliably have on harvest day, the herd size and number of feeding groups, whether you already have a bunker, and the local cost of film, fuel and contractor time. With those, the person-hour calculation above, the minimum feed-out rate for a bunker and the film cost per tonne for bales can all be worked out in an afternoon.
Tsingtao Jummos Agricultural Technology Co., Ltd., based at No.173 Jufeng Road, Qingdao, China, supplies equipment for bale-based silage systems, including stationary baler-wrappers and the 9QZ-2150A self-propelled silage harvester baler wrapper, along with silage film through its sister brand Silopak. Send us those figures and we will work through the comparison with you, including telling you plainly when a bunker would serve you better.
Frequently Asked Questions
Is baled silage more expensive than bunker silage?
Usually yes per tonne, mainly because bales use more plastic and handling per tonne, and small bales use more film than large ones. But a bunker needs a permanent structure, a large crew on harvest day and a herd big enough to keep the face moving. For small and medium farms, bales can be cheaper overall once those factors are counted.
Does a harvest-and-bale system need less labour?
It needs fewer people at any one time, often one instead of four or more. Total person-hours per tonne can be similar to chop-and-haul, because the all-in-one machine is slower. The real difference is that the work is spread over more days with one person rather than concentrated into a few days with a full crew.
How far can fields be from the storage site?
With chop-and-haul, longer distances need more trucks to keep the harvester working, and very long hauls quickly become uneconomic. With harvest-and-bale, distance matters much less on harvest day, because sealed bales can be collected later at whatever pace suits the farm.
Can I use both systems on the same farm?
Yes, and many farms do. A bunker for the main crop and bales for later cuts, outlying fields or silage sold to other farms combines the low cost per tonne of the clamp with the flexibility of bales.
Reviewed by Sue Su, Marketing Director at Tsingtao Jummos Agricultural Technology Co., Ltd., a supplier of baler wrappers, silage harvesting equipment, TMR mixers and manure handling equipment based in Qingdao, China. Last reviewed 20 November 2026.

