An all-in-one silage harvester baler is a single self-propelled machine that cuts a standing crop, chops it, cracks the maize kernels, presses the chopped forage into round bales and seals each bale in stretch film, all in one pass across the field. Until recently, getting from standing maize to sealed silage meant a chain of separate machines: a forage harvester, a fleet of trailers or trucks, a packing tractor at the bunker, or a stationary baler and wrapper fed by a loader. The all-in-one approach collapses that chain into one machine and one operator. It is a genuinely new category, and according to Jummos, it is so new in China that only one factory currently builds it. This article explains what the machine does, how it works stage by stage, where it fits on a farm and where it does not, and what to check before buying into a category with a short track record.

all-in-one silage harvester baler wrapper, self-propelled machine that cuts, chops, bales and wraps silage

The Problem It Solves: Too Many Links in the Silage Chain

Silage is a race against air. From the moment a maize plant is cut, its cells keep respiring and burning sugar, and moulds and yeasts start working on the exposed forage. The whole point of ensiling is to stop that by excluding oxygen so that lactic acid bacteria can take over, and every hour between cutting and sealing is an hour of avoidable loss. On a conventional system that gap can be long, because the chopped crop has to be loaded, hauled, tipped, spread, packed and finally covered, and each step depends on the one before it keeping pace.

That dependency is where most of the trouble lives. A forage harvester can only work as fast as the trucks can take its output away, and the trucks can only tip as fast as the packing tractor can spread and compact the load at the bunker. If one truck breaks down or one driver fails to turn up, the whole operation slows, and the forage already in the clamp sits partly packed and uncovered. Farms that rely on contractors face a second constraint: the contractor arrives when the contractor can, which is not always when the crop is at its best.

The stationary baler-wrapper route, which is common on smaller farms in China and elsewhere, shortens the storage side but not the harvest side. Chopped forage still has to be cut, hauled to the yard and loaded into the baler by hand or by loader, so the crop still waits. An all-in-one machine removes those waiting steps. The forage goes from the plant to a sealed bale inside the same machine, usually within moments, and the bale is set down in the field already protected.

How the Machine Works, Stage by Stage

The 9QZ-2150A self-propelled silage harvester baler wrapper that Jummos supplies is a good example of the category, and its specification shows how the stages fit together. Each stage does a job that would otherwise need a separate machine.

Stage What happens 9QZ-2150A specification
Cutting The header cuts the standing crop at the base and gathers it Straight header, 2 drums, 12 harvesting blades, 2010 mm cutting width
Feeding Rollers grip the cut crop and feed it evenly into the chopper 4 feed rollers
Chopping A rotating disc of knives cuts the crop to a set length Disc type, 12 chopping blades, 10 or 20 mm cut length
Kernel processing Maize kernels are cracked so cattle can digest the starch Rubbing-plate kernel processor
Baling Chopped forage is pressed into a dense round bale Φ55 × 52 cm bales, 45 to 60 bales per hour
Wrapping Each bale is sealed in stretch film to exclude air 2 film racks
Drive and power The machine carries its own engine and travels under its own power 128.7 kW at 2400 r/min, hydraulic drive, manual transmission, disc brakes, 2 to 6 km/h working speed

Two of those stages deserve a closer look because they decide feed quality rather than just throughput. The cut length setting, 10 or 20 mm, controls how well the forage packs and how much effective fibre it carries into the ration; shorter chop packs tighter, longer chop gives the rumen more to work with. The kernel processor matters because a whole maize kernel can pass through a cow largely undigested, taking its starch with it. Cracking the kernels at harvest is what turns maize silage into the high energy feed it is supposed to be, and an uncracked crop can look perfectly good in the bale while quietly wasting a share of its energy.

The bale itself is small by Western standards, at 55 cm across and 52 cm long. That is the same Φ550 × 520 mm size made by compact stationary balers such as the BalerPro 55, and based on Jummos specifications for balers making this size, a bale typically weighs somewhere between 50 and 120 kg depending on crop and moisture. Small bales are a deliberate choice for the markets this machine serves: they can be moved with light equipment, sold individually and fed out one at a time.

side profile of a self-propelled silage harvester baler wrapper showing header, cab, baler and film wrapper

Why Sealing at the Point of Harvest Matters

The single biggest technical advantage of the all-in-one design is not speed, it is timing. In any silage system the goal is to get chopped forage packed and sealed before it loses sugar and before aerobic organisms establish themselves. Our guide to silage bales gives the working rule for baled forage: wrap within a couple of hours of baling, and certainly on the same day. A machine that wraps each bale moments after forming it meets that rule by design rather than by good organisation on the day.

It also changes what happens when something goes wrong. If a truck breaks down in a chop-and-haul system, forage piles up, either on the trailer or half packed in the clamp, and the clock keeps running on all of it. If an all-in-one machine stops, the bales already made are sealed and safe, and the crop still standing in the field is simply waiting to be cut. Problems stop the harvest rather than spoiling what has already been harvested. For farms in regions with unreliable contractors or unpredictable rain, that difference can matter more than raw output per hour.

There is a quality consistency benefit too. In a bunker, the silage at the edges, the shoulders and the top is notoriously harder to pack and protect, and it is where most spoilage concentrates. Every small bale, by contrast, is packed by the same chamber to the same density and sealed by the same wrapper. Variation between bales still exists, driven by crop moisture and film integrity, but there is no equivalent of the poorly packed bunker shoulder.

What One Operator Can Do

The machine is designed for one-person operation: a single operator in the cab controls cutting, chopping, baling and wrapping. That is a substantial change from a conventional chop-and-haul crew, which typically needs someone on the harvester, a driver for each truck or trailer, and at least one tractor driver packing at the bunker. In regions where skilled seasonal labour is scarce or expensive, reducing a harvest crew to one person is often the main reason buyers look at this category at all.

The output to plan around is 45 to 60 bales an hour, which over an eight hour working day comes to roughly 360 to 480 sealed bales. At the bale weights given above, that is very roughly 2 to 7 tonnes of silage an hour, depending on how heavy the bales are in your crop. That is far slower than a large conventional forage harvester, which can chop many times more per hour if enough trucks keep up with it. The comparison that matters is not tonnes per hour of the harvester alone, but tonnes per hour per person across the whole operation, including the truck drivers and the packing tractor that a conventional harvester cannot work without.

The bales still have to be collected from the field. Because they are sealed, there is no rush: collection can happen the next day or the next week, with a loader and trailer, without the forage deteriorating while it waits. That decoupling of harvest from transport is one of the quieter advantages of the system, and it is the opposite of chop-and-haul, where transport has to keep exact pace with the harvester.

Buyers usually ask us about bales per hour first, but the better question is how many people your harvest needs and what happens to the crop when one of them doesn’t turn up. This machine answers that differently from anything else we supply. It is not the fastest way to make silage, it is the way that needs the fewest people and leaves the least crop waiting in the open. Sue Su, Marketing Director, Tsingtao Jummos Agricultural Technology Co., Ltd.

Where It Fits, and Where It Does Not

An all-in-one silage harvester baler suits a specific set of farms well. Small and medium dairy and beef units without a bunker, or without a herd large enough to keep a bunker face moving, gain a way to make chopped maize silage in units they can feed out one at a time. Silage supply businesses, which make bales and sell them to smaller livestock farms, gain a machine that produces a saleable product directly in the field. Contractors serving many small, scattered fields gain a self-contained unit that needs no trucks, no clamp and no packing crew at each site. And farms in areas where harvest labour is the binding constraint gain the most of all.

It suits other farms less well, and it is worth being plain about that. A large dairy with established bunker infrastructure and a dependable contractor will usually make silage more cheaply per tonne by chopping into the clamp, because bunkers use far less plastic per tonne and large forage harvesters move far more material per hour. Small bales also carry more film per tonne of silage than large ones, simply because a small cylinder has more surface relative to its volume. The machine is designed for maize stalks and forage grass, so long dry hay or straw is a job for a conventional baler, not for this one. And at 7080 x 2250 x 4820 mm in working state, it needs gateways, lanes and field access that can take a machine of that size.

Handling is the last practical consideration. A bale of 50 to 120 kg is too heavy to lift safely by hand on a routine basis, so most farms need a small loader, a bale grab or a tractor with a front loader to move bales from field to store and from store to feed. That equipment is modest compared with what a bunker system requires, but it should be in the plan from the start.

A New Category, Even in China

Small chopped-maize silage bales are a familiar product in China, commonly made with stationary baler-wrappers fed from separate harvesters, the kind of equipment Jummos has supplied for years. The all-in-one machine is the next step: putting the harvester, the baler and the wrapper on one self-propelled chassis. According to Jummos, the category is very new in China and only one factory currently produces it, which makes it an early stage technology even in the country where it was developed.

That is an opportunity and a caution in equal measure. Early adopters gain a capability that most of their competitors do not have, and in markets where labour and timeliness are under pressure that can be a real advantage. Early adopters also accept that the machine has less field history than established designs, that operating experience is still accumulating, and that parts and service networks outside China are thinner than for long established machines. Neither point is a reason to avoid the category, but both are reasons to buy carefully.

Questions to Ask Before Buying a New-Category Machine

With any machine that has a short track record, the questions that protect you are about support rather than specification. These are the ones worth putting to any supplier, Jummos included, in writing before ordering.

  • Spare parts. Which wear parts are stocked, how quickly they ship to your country, and whether a starter kit of blades, belts and film rack parts can be supplied with the machine.
  • Operator training. Whether training is included, in what language, and whether it covers cut length, kernel processor and wrapper settings, not just driving.
  • Film supply. What film the wrapper takes, in what roll size, and whether that film can be sourced reliably in your market. Our article on the 250 mm silage film baler covers film for small bales.
  • Field references. Where the machine is working, in which crops, and for how many seasons.
  • Warranty mechanism. Who pays freight and labour on a warranty part, and how many days from report to shipment.
  • Transport and import. Shipping weight and dimensions, how the machine is packed, and what documents come with it.

A supplier that answers these clearly is giving you the information you need to manage the risk of being an early adopter. One that cannot answer them is telling you something about the support you would receive after delivery.

Jummos and the 9QZ-2150A

Tsingtao Jummos Agricultural Technology Co., Ltd., based at No.173 Jufeng Road, Qingdao, China, supplies the 9QZ-2150A self-propelled silage harvester baler wrapper alongside its range of baler wrappers, TMR mixers and manure handling equipment, and supplies silage film through its sister brand Silopak. Full specifications are on the product page. If you are weighing this machine against a conventional silage system, send us your herd size, field layout and current harvest arrangements, and we will give you a straight assessment of whether it fits.

Frequently Asked Questions

What is an all-in-one silage harvester baler?

It is a self-propelled machine that cuts a standing crop, chops it, cracks the maize kernels, presses the chopped forage into round bales and wraps each bale in stretch film, all in one pass. It replaces the separate forage harvester, trucks, packing tractor and baler-wrapper of a conventional silage system with one machine and one operator.

How many bales can it make per hour?

The 9QZ-2150A is rated at 45 to 60 bales per hour, roughly 360 to 480 bales over an eight hour day. Each bale measures Φ55 × 52 cm and typically weighs somewhere between 50 and 120 kg depending on crop and moisture.

Is it faster than a forage harvester?

No. A large conventional forage harvester chops far more tonnes per hour, provided enough trucks and drivers keep up with it. The all-in-one machine’s advantage is that it needs one operator instead of a crew, seals the forage immediately, and leaves no harvested crop waiting unprotected if work stops.

Which crops can it harvest?

It is designed for maize stalks, including whole-plant maize for silage, and for forage grass. It is not intended for long dry hay or straw, which are better handled by conventional balers.


Reviewed by Sue Su, Marketing Director at Tsingtao Jummos Agricultural Technology Co., Ltd., a supplier of baler wrappers, silage harvesting equipment, TMR mixers and manure handling equipment based in Qingdao, China. Last reviewed 18 November 2026.